Tip: if you're looking for drivers, manuals, or other technical support resources, search in the Stevens support site instead.




Teledesign TS4000 900MHz UHF/VHF

True cloud-based sensor configuration, logging, reporting and data analysis all-in-one.


Shark (RS232/RS485 Bluetooth Serial Adapter)


A cloud-based interface to configure hardware, visualize data, analyze measurements, manage alarms, calculations, and set up data routing.

MEASUREMENTS TO MIND (M2M) is a growing suite of Stevens products that embraces cloud-computing with an all-inclusive vision of shortening the communication path from the sensors to data on-line. That is, what the sensors MEASURE the MIND sees.

The product finder lets you explore our catalog visually and filter products by type of monitoring, manufacturer, and more.


SOLO (smart SDI-12 power manager)
JL-2 (solar charge controller)
Power Supplies
Solar Panels

Smart SDI-12 power manager that also provides remote power cycling.

The product finder lets you explore our catalog visually and filter products by type of monitoring, manufacturer, and more.

The product finder lets you explore our catalog visually and filter products by type of monitoring, manufacturer, and more.


Reliable, 2-way cellular modem that’s easy to set up.

Part # 93950

  • More

    Power input

  • More

    USB (allows connection to computer for configuration changes instead of via cell connection)

  • More

    Standard RS-232 serial port (connect to logger or smart sensor)

  • More

    Status LEDs

  • More

    GPS antenna connector

  • More

    Cellular antenna


Stevens' MEASUREMENTS TO MIND strategy maximizes reliability of your remote monitoring network and makes it simple to connect your station directly to the cloud.

Cell-Net is a simple cellular telemetry solution for new or existing remote monitoring stations. Cell-Net offers a web-based configuration utility that makes it easy to install and configure forwarding of remote data to any destination.

Unlike typical cellular modems which have a constant high power draw, Cell-Net operates almost entirely in an ultra-low power mode yet still provides the benefits of 2-way communications, and optimizes successful transport of data for maximum reliability.

  • Designed specifically for easy configuration and provisioning for remote sites that are costly to visit.
  • Approximately 20X typical improvement in power consumption vs. typical cellular telemetry.
  • Provides the benefits of a 2-way connection without high power consumption.
  • Data transmission via FTP, HTTP protocols (or both simultaneously) or IP protocol.
  • Intelligent data management, data buffering, and network verification to ensure successful transmission of critical data.
  • Can be used with your choice of cellular carriers (3G GSM or 3G CDMA).
  • Integrated GPS for time, longitude and latitude.
  • Perfect for any application, monitoring any parameters.

Unique Features

  • Easy configuration: Configure via the web-based portal or by connecting to a PC and using an intuitively designed Windows program. No custom programming or scripts required.
  • Smart power management: Cell-Net features an ultra-low-power mode that consumes just 1.6mA at idle (that’s less than 1% of a typical cell modem). When transmitting, power draw is similar to other modems, but this is only for very short periods at user-controlled transmission intervals.
  • Data management: Cell-Net will listen for a connected logger or smart sensor to receive data in the buffer before transmitting. Once received, data can either be transmitted immediately, or after the buffer exceeds a defined size, or transmitted based on a user-defined interval.
  • Redundancy: Data is transmitted for current reporting cycle and the last reporting cycle.
  • Reliability: Cell-Net verifies connection with cell network and HTTP server connection before data is sent. If no connection is available or if data reception is not confirmed, data is saved and sent the next scheduled transmission.
  • Data flexibility: Forward your data to any destination to access with any software platform, like Aquarius or our own cloud-based Stevens-Connect.
  • Connect directly to the cloud: Provides direct IP connectivity to data loggers and smart sensors through a standard RS-232 serial port. No other interface hardware required.
  • Predict and prevent problems: In addition to internal diagnostics, station and transmission health and performance data can be included in each transmission.

Up to 20x better power efficiency vs. typical cellular modems.

The key to the extreme power efficiency of Cell-Net is its “hybrid” approach to 2-way communications. Not only does it consume less power than typical cell modems when in standard 2-way communications mode, but it also offers an ultra-low power mode that sacrifices some responsiveness in two-way connectivity for an extremely low power consumption that makes it suitable for remote stations monitoring critical data.




Typical cellular modems

Full 2-way communication mode

On demand



Power consumption at idle

150 mA

220 mA

Ultra-low power mode


Power consumption at idle

1.6 mA



Transmit new data

On schedule or when triggered



Download new configuration data

On schedule or when triggered


Dead simple setup and configuration.

Anytime, anywhere, any device.

All configuration and programming of the remote Cell-Net is done online via the cloud-based Stevens-Connect. Setup in 3 steps:


Connect to data logger


Connect to power source


Configure data handling (frequency, redundancy, destination) with a simple online GUI

Shop Online

Technical Specifications

Current consumption

Listen/trigger mode/idle

1.6 mA

Data receive/store/prepare for transmission

150 mA

Data transmit

250 mA


Input voltage

10 to 18 VDC

TX output power

24.3 dBm (270 mW)



1 3/8” (3.5 cm) x 5 1/8” (13 cm) x 3 3/4” (9.7 cm)


10.78 oz (305.6 g)


Operating temperature

-30°C to 65°C (SIM Card selection may limit this range for GSM version)

Storage temperature

-40°C to 85°C (SIM Card selection may limit this range for GSM version)



Indicates power to the unit


Indicates if GPS does not have location fix


Indicates if there is a connection to the tower


Built-in self test


Communication with data logger/smart sensors


Communication with PC


Cellular antenna


GPS antenna



Power cable with flying leads, dipole dual-band cellular 800/1900 MHz antenna, USB cable.

Commands can be sent remotely through a web interface to switch Cell-Net into full 2-way communication mode. When it's not in full 2-way mode, the command will be received during the next scheduled transmittal of data (each time data is sent from the remote site, Cell-Net also downloads any new configuration files—the new configuration would contain the command to switch to 2-way mode). In full 2-way mode, the modem is "on-line" and actively listening for commands, and can respond immediately when commands are sent. Power consumption is higher at idle however (150 mA). A new configuration file will also deliver the command to switch back to ultra-low power mode.
Typical cellular modems are always in full 2-way communicate mode, and is always "on-line" and actively listening for commands, responding immediately when commands are sent. Power consumption is always high (220 mA at idle) however, which is why cellular has traditionally not been a practical option for very remote sites that monitor critical data.
When in ultra low-power mode, new data that is received from an attached data logger or smart sensor is buffered in internal memory and transmitted when:
  1. the next interval of a pre-defined schedule occurs

  2. immediately, if Cell-Net has been programmed to transmit data when it receives specific data from the attached data logger or smart sensor (this is called "triggered" data). Users also have control over a delay period after the data is received from the logger but before it is transmitted, to account for variable length pauses from different sensors.
Tip Title
In ultra-low power mode, each time data is transmitted Cell-Net will check for a new configuration (that has been created via a web-based interface). Since data is transmitted only when a scheduled interval occurs or if it has been programmed to send when it receives new data (triggered data), new configurations are not able to be downloaded as soon as they are sent.